Searching for Very High Energy Emission from Pulsars Using the High Altitude Water Cherenkov (HAWC) Observatory

There are currently over 160 known gamma-ray pulsars. While most of them are detected only from space, at least two are now seen also from the ground. MAGIC and VERITAS have measured the gamma ray pulsed emission of the Crab pulsar up to hundreds of GeV and more recently MAGIC has reported emission at $\sim2$ TeV. Furthermore, in the Southern Hemisphere, H.E.S.S. has detected the Vela pulsar above 30 GeV. In addition, non-pulsed TeV emission coincident with pulsars has been detected by many groups, including the Milagro Collaboration. These GeV-TeV observations open the possibility of searching for very-high-energy (VHE, > 100GeV) pulsations from gamma-rays pulsars in the HAWC field of view.Comment: Presented at the 34th International Cosmic Ray Conference (ICRC2015), The Hague, The Netherlands. See arXiv:1508.03327 for all HAWC contribution

Results of a self-triggered prototype system for radio-detection of extensive air showers at the Pierre Auger Observatory

We describe the experimental setup and the results of RAuger, a small radio-antenna array, consisting of three fully autonomous and self-triggered radio-detection stations, installed close to the center of the Surface Detector (SD) of the Pierre Auger Observatory in Argentina. The setup has been designed for the detection of the electric field strength of air showers initiated by ultra-high energy cosmic rays, without using an auxiliary trigger from another detection system. Installed in December 2006, RAuger was terminated in May 2010 after 65 registered coincidences with the SD. The sky map in local angular coordinates (i.e., zenith and azimuth angles) of these events reveals a strong azimuthal asymmetry which is in agreement with a mechanism dominated by a geomagnetic emission process. The correlation between the electric field and the energy of the primary cosmic ray is presented for the first time, in an energy range covering two orders of magnitude between 0.1 EeV and 10 EeV. It is demonstrated that this setup is relatively more sensitive to inclined showers, with respect to the SD. In addition to these results, which underline the potential of the radio-detection technique, important information about the general behavior of self-triggering radio-detection systems has been obtained. In particular, we will discuss radio self-triggering under varying local electric-field conditions.Comment: accepted for publication in JINS

Characterization of nanodimensional Ni-Zn ferrite prepared by mechanochemical and thermal methods.

Nickel zinc ferrite nanoparticles, Ni1−xZnxFe2O4 (x = 0, 0.2, 0.5, 0.8, 1.0), with dimensions below 10 nm have been prepared by combining chemical precipitation with high-energy ball milling. For comparison, their analogues obtained by thermal synthesis have also been studied. Mössbauer spectroscopy, X-ray diffraction, and magnetic measurements are used for the characterization of the obtained materials. X-ray diffraction shows that after 3h of mechanical treatment ferrites containing zinc are formed, while 6h of treatment is needed to obtain NiFe2O4. The magnetic properties of the samples exhibit a strong dependence on the phase composition, particle size and preparation method

Kinematic alignment in total knee arthroplasty

Kinematic alignment (KA) is an alternative philosophy for aligning a total knee replacement (TKR) which aims to restore all three kinematic axes of the native knee. Many of the studies on KA have actually described non-KA techniques, which has led to much confusion about what actually fits the definition of KA. Alignment should only be measured using three-dimensional cross-sectional imaging. Many of the studies looking at the influence of implants/limb alignment on total knee arthroplasty outcomes are of limited value because of the use of two-dimensional imaging to measure alignment, potentially leading to inaccuracy. No studies have shown KA to be associated with higher complication rates or with worse implant survival; and the clinical outcomes following KA tend to be at least as good as mechanical alignment. Further high-quality multi-centre randomized controlled trials are needed to establish whether KA provides better function and without adversely impacting implant survival

Competition between preslip and deviatoric stress modulates precursors for laboratory earthquakes

Abstract Variations in elastic wave velocity and amplitude prior to failure have been documented in laboratory experiments as well as in a limited number of crustal earthquakes. These variations have generally been attributed to fault zone healing, changes in crack density, or pore fluid effects modulated dilatation or fault slip. However, the relationships between amplitude and velocity variations during the seismic cycle, and the underlying mechanisms of precursors to failure remain poorly understood. Here, we perform frictional shear experiments and measure the evolution of elastic wave velocity and amplitude throughout the laboratory seismic cycle. We find that elastic amplitudes and velocities undergo clear preseismic variations prior to fault failure. While preseismic amplitude reduction occurs early in the interseismic period, wave speed reduces later, just prior to failure. We perform a complementary set of stress oscillation experiments to quantify the response of seismic amplitudes and velocities to variations in the stress tensor. Taken together, our results indicate that preseismic amplitude variations are primarily controlled by fault slip rate and acceleration. On the other hand, elastic velocity responds to a combination of fault preslip which reduces seismic wavespeed and increasing stress in the wallrock, which increases wavespeed. Our data show that precursory changes in seismic wave speed may be more common than previously thought because they are masked by changes in wallrock stress. These results underscore the importance of continuous and long-term time-lapse monitoring of crustal faults for seismic hazard assessment and potential precursors to failure

Optimization and thermal stability of TiAlN-Mo multilayers

In this work we focus on the optimization and thermal stability of nanocomposite TiAlN/Mo multilayers that were produced by reactive magnetron sputtering on high-speed steel substrates, with modulation periods below 5 nm. These multilayers were annealed between 600– 900 ºC for 1 h in a vacuum furnace. Preliminary X-ray diffraction results reveal that these coatings are very stable up to 900 ºC, since the multilayer chemical modulation is not severely affected. At intermediate annealing temperatures the modulation period decreases due to interdiffusion at the interface, resulting in a thicker interface between metal/nitride and hence decreasing the thickness of those layers.Portuguese FCT/MCES scientific program

Observation of the Moon shadow with the ANTARES neutrino telescope

International audience; ANTARES is currently the largest neutrino telescope on the Northern Hemisphere. It consists of a three-dimensional array of PMTs deployed at a depth of 2475 m off-shore the Toulon cost in France. Operating since May 2008 in its full configuration, it aims to detect high-energy cosmic neutrinos. In the absence of an astrophysical standard cand le, a possible way to measure the angular resolution and the pointing accuracy for a neutrino telescope is to look at "Moon shadow" in the atmospheric muon flux. The analysis method and the first results of the observation of the Moon shadow with ANTARES will be presented and discussed. The data, analysed in this work,were collected between Jan 31st, 2007 and Dec 31th 2010, for a total live time of 814 days